computer problem

Plain Old Jane · 02-03-2005, 06:54 PM

I have a problem here, fixxing a friends wifi, it works... to some extent...

there are two computers here, both compaq presario 2200's with built in wireless. one works now that i fiddled with firewall and wep settings, the other I did the same thing and it doesnt work.

Any thoughts on how to fix it?

raublekick · 02-03-2005, 06:57 PM

what doesn't work about it? can it see the router or whatever at all? do the networking setings come up? is the signal strength just too low?

GT2000 · 02-04-2005, 11:56 AM

Yes, best thing to do in this case, is to uninstall the card, reset the router to defaults, and leave WEP disabled to start with. Then re-install the card, and then see if it's able to pick up on the router. I've had a ton of trouble calls like this, in many cases disabling WEP took care of it, so I'd then proceed to just setup mac filters for some basic protection, that way your average joe won't be able to jack into your network. Even with WEP enabled, someone who really wanted to could easily surf on your dime.

So give that a try, and let us know, also, try to be a little more specific, that always helps.

Plain Old Jane · 02-04-2005, 01:15 PM

specifics:

cable modem is hooked up to the wireless router, 1 computer is directly hooked up to the router (the one whose wirless did not work.) but no setup software or control panel was readily available, but I could have 168.ip what ever'd into it if i needed to, no wep on, factory defaults on. Both computers are owned by teenage girls, so spy ware abound prolly. It'd take a whole afternoon to clear the crap off them.

I did not try reinstalling drivers, but I shall next time I'm over this weekend.

Jesse · 06-20-2006, 08:53 PM

This thread got way out of hand.

Locked.

02-03-2005, 06:54 PM	#1
Plain Old Jane i hate vagina Join Date: Oct 2004 Posts: 841	computer problem I have a problem here, fixxing a friends wifi, it works... to some extent... there are two computers here, both compaq presario 2200's with built in wireless. one works now that i fiddled with firewall and wep settings, the other I did the same thing and it doesnt work. Any thoughts on how to fix it? __________________ Scary Monsters and Nice Sprites.

02-04-2005, 11:56 AM	#3
GT2000 Playing God @ Your Xpense Join Date: Oct 2004 Location: Va Beach, Va Posts: 2,040	Yes, best thing to do in this case, is to uninstall the card, reset the router to defaults, and leave WEP disabled to start with. Then re-install the card, and then see if it's able to pick up on the router. I've had a ton of trouble calls like this, in many cases disabling WEP took care of it, so I'd then proceed to just setup mac filters for some basic protection, that way your average joe won't be able to jack into your network. Even with WEP enabled, someone who really wanted to could easily surf on your dime. So give that a try, and let us know, also, try to be a little more specific, that always helps. __________________ Hop in, strap down, and hold on tight.

02-04-2005, 01:15 PM	#4
Plain Old Jane i hate vagina Join Date: Oct 2004 Posts: 841	specifics: cable modem is hooked up to the wireless router, 1 computer is directly hooked up to the router (the one whose wirless did not work.) but no setup software or control panel was readily available, but I could have 168.ip what ever'd into it if i needed to, no wep on, factory defaults on. Both computers are owned by teenage girls, so spy ware abound prolly. It'd take a whole afternoon to clear the crap off them. I did not try reinstalling drivers, but I shall next time I'm over this weekend. __________________ Scary Monsters and Nice Sprites.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Turn your computer on, got no post (beeps), error code on board, etc?	GT2000	Computers	6	11-17-2005 10:59 PM
the problem with star trek...	heX	Miscellaneous	12	03-31-2005 09:36 PM
since we've been talking about computer games.....	raditz	Miscellaneous	9	01-11-2005 11:08 PM

02-03-2005, 06:57 PM	#2
raublekick Moderator Join Date: Oct 2004 Location: Lancastuh, PA Posts: 1,678	what doesn't work about it? can it see the router or whatever at all? do the networking setings come up? is the signal strength just too low?

06-20-2006, 08:53 PM	#5
Jesse Administrator Join Date: Oct 2004 Posts: 812	This thread got way out of hand. Locked.